PIC16F873T-04E/SO【PDF 136/218 页】IC MCU FLASH 4KX14 EE 28SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3889

132页 133页 134页 135页 [136页]137页 138页 139页 140页

PIC16F87X

DS30292C-page 22

2001 Microchip Technology Inc.

2.2.2.5

PIR1 Register

The PIR1 register contains the individual flag bits for

the peripheral interrupts.

Note:

Interrupt flag bits are set when an interrupt

condition occurs, regardless of the state of

its corresponding enable bit or the global

enable bit, GIE (INTCON<7>). User soft-

ware should ensure the appropriate interrupt

bits are clear prior to enabling an interrupt.

REGISTER 2-5:

PIR1 REGISTER (ADDRESS 0Ch)

R/W-0

R-0

R/W-0

PSPIF(1)

ADIF

RCIF

TXIF

SSPIF

CCP1IF

TMR2IF

TMR1IF

bit 7

bit 0

bit 7

PSPIF(1): Parallel Slave Port Read/Write Interrupt Flag bit

= A read or a write operation has taken place (must be cleared in software)

= No read or write has occurred

bit 6

ADIF: A/D Converter Interrupt Flag bit

= An A/D conversion completed

= The A/D conversion is not complete

bit 5

RCIF: USART Receive Interrupt Flag bit

= The USART receive buffer is full

= The USART receive buffer is empty

bit 4

TXIF: USART Transmit Interrupt Flag bit

= The USART transmit buffer is empty

= The USART transmit buffer is full

bit 3

SSPIF: Synchronous Serial Port (SSP) Interrupt Flag

= The SSP interrupt condition has occurred, and must be cleared in software before returning

from the Interrupt Service Routine. The conditions that will set this bit are:

SPI

- A transmission/reception has taken place.

I2C Slave

- A transmission/reception has taken place.

I2C Master

- A transmission/reception has taken place.

- The initiated START condition was completed by the SSP module.

- The initiated STOP condition was completed by the SSP module.

- The initiated Restart condition was completed by the SSP module.

- The initiated Acknowledge condition was completed by the SSP module.

- A START condition occurred while the SSP module was idle (Multi-Master system).

- A STOP condition occurred while the SSP module was idle (Multi-Master system).

= No SSP interrupt condition has occurred.

bit 2

CCP1IF: CCP1 Interrupt Flag bit

Capture mode:

= A TMR1 register capture occurred (must be cleared in software)

= No TMR1 register capture occurred

Compare mode:

= A TMR1 register compare match occurred (must be cleared in software)

= No TMR1 register compare match occurred

PWM mode:

Unused in this mode

bit 1

TMR2IF: TMR2 to PR2 Match Interrupt Flag bit

= TMR2 to PR2 match occurred (must be cleared in software)

= No TMR2 to PR2 match occurred

bit 0

TMR1IF: TMR1 Overflow Interrupt Flag bit

= TMR1 register overflowed (must be cleared in software)

= TMR1 register did not overflow

Note 1: PSPIF is reserved on PIC16F873/876 devices; always maintain this bit clear.

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

- n = Value at POR

’1’ = Bit is set

’0’ = Bit is cleared

x = Bit is unknown

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式